Thursday, 31 December 2020

Re-Homing A Spitfire

 So from going from posting quite regularly to nothing for 3 years (and then forgetting to publish it!) TO leaving it another 18ish months here goes.


The car was previously stored at the in laws house where I could pop down, have a tinker in the machine mark tent/garage it was in and come home to the warm.  The tent was very exposed to the wind due to location but held up very very well, with the help of lots of tape!  One morning I got a call, it had finally given up, and in a big way, ripping right down the ridge. So it's early January 2019 and I need to find a way to transport the car circa 10 miles home to the garage but wanted to do so as cheaply as possible!

Step in the next door neighbour who has a farm and the next day the car is on the trailer being transported.



I didn't follow too close as I didn't want to explain to the insurance that my car had come off a trailer and crashed into my car!

And she's home!


So now she lives in the garage, advantage being its much easier to pop out and mess about for a short while at my leisure.  Dis-advantage is that is alot more cramped, and the car tends to be used as a shelf!




Tuesday, 16 April 2019

It's Alive...... Sort of

Originally drafted in April 2019 but never posted as I didn't get it finished, just like the car!

A lot of work has gone in recently but a part which has been a real pain for me was the ignition/fuelling.

After the car being off the road for so long I was mega keen to get it started in a true Frankenstein moment.  I hooked everything up, turned the key and.... click. Nothing else.

I managed to find the source of the initial faul, the starter solenoid.  This was quickly replaced, and after making sure it had a good ground (fix it fully to the body tub).  Next up was the condenser, this cheap part caused me a day of heart ache while I figured out it was faulty.  For the cost, just swap it out with the point.

So that was it, I had spark, I had turn over and had fuel, but still it just wouldn't go.  It would fire and roar with a bit of Easy Start, and then just a quickly die.  More fault finding, walking away and coming back with no solutions until it was highlighted regarding the vacuum hose between the carbs.  If this is not on it will not run.

So the moment of truth, and it started (with the choke) and reved very very very high.  Kill the engine, it obviously needs setting up

A little bit of investigation and the reason for this was it was sucking in lots and lots of air as the carbs weren't fully tightened and the cabs should be set up to approximately, 12 flats out on the mixture nut. This is a good starter for 10!

Saturday, 23 July 2016

Replacement Battery Box

As you can imagine, a steel battery box, in a 30 year old car is a prime location for rust.  Mine was subject to this, with a few small holes right on the curve.  As with everywhere else on the car I tried to repair this, however owing to the location (on the curve) and my poor welding skills, the repair was bad to say the least!

So the decision was made to replace the battery box.  This means drilling out the spot welds (all 10,000 of them, or at least that's how it felt!) bending back the brackets and pulling out the old box


Terrible
repair visible in the middle back

One bracket free!







All ready to prise out the old box!

As you can see I previously stripped the bulkhead and lightly painted and then abandoned it, this area needs some work!







The new box, disappointingly, does not come with the connection for the drainage pipe.  My first thought was to cut the old one out and weld it in but then I had a brainwave to use a pipe insert.  I checked the size and it's fine so that's a job for the future.








Old spot welds are flatted and a dusting of weld through primer.  I spray this on so that there is no bare metal under the lip of the new box







New box welded in and the spot welds dressed flat.

You'll notice that the back edge (which has got to be bent up to meet the kick in the bulkhead) hasn't had any spot welds in.  I have done this as the box is not moving out of place and so I didn't see the need for them






More updates to come of the previous works, but these will come in nor particular order!

Sunday, 21 February 2016

All Happening In The Background

So it's been a while since an update and from the outside due to lack of updates its may seem that there has been little to no progress.  But it's been happening in the background.  So over the next few days/weeks I will try to put up some updates of the various different stages the build has been through.
Stay tuned!

Sunday, 23 February 2014

Brake drum adjusters refurb

I've managed to get my drive to work on the car again but among others things that have been done I thought I'd do a quick write up on how to return your red broke drum adjusters.
I found that mine would turn difficultly and also didn't feel the flt so you know how much you had adjusted it. Whilst they are one £8-9 to but why not have go at fixing your existing!

My left one was quite cruddy as you can see
So the first step to do is full wind in the adjustror from the trrar as it comes out of the front, when it gets to the point that you can no longer turn it it'll take one !pre turn with so!e need nose pliers.
After this you can simply push\pull the adjustor cone out, while we have this it's time to clear it up, put the threads on the wired wheel as remeber these are always exposed under the car so keeping them clean coated will help protect them. The cone itself just needs too be cleaned with a cloth, no abrasives and inspect it to check it still has the flats pon it to indicate adjustment.

You'll have noticed that that while taking the adjustor cone out it pushed out the shoe spacers, these can easily be pulled out but make sure you note which way they are tapered otherwise the adjustors won't work.

Shown how they are tapered is in this photo
Against while these are handy out then on the wire wheel to clean them up

Next tackle the actual adjustoer housing itself. Rather than strip and re-paint I opted to wire brush the thick of and cloth clean the insides. Its as clean as its going to get!

Now its time to put it back together and remember, Copper slip, let's not have these seazing up again! 
Copper slip the shoe spaces and re-insert, make sure they aren't pushed in top close as you still have to fit the adjustor from the front.
Finally copper slip the threads of the adjustor and re-fit, loosing back into place and you're done.

When re fitting I intend the put more copper slip in the hole as shown above, Grantred because it will be in the brake drum it will pick up some dust but my thoughts are it stops the dust getting to the spacers/pistons.

Hopefully this helps someone!

Tuesday, 9 April 2013

The Painting Has Begun

Well this update has been a long time coming, don't think it's because I havent done anything because I have but now that I am temporarily out of work I can spend more time on my projects.
I thought for something different today I'd tackle some painting (being as recently I'd been welding, learn by doing -more on that in future)
First I needed somewhere to paint, so after looking a I decided a nice big poly tunnel should do, it would help keep the temperature up required for painting

Next the pannel, I picked the boot lid as its small enough to practice on. After stripper all of the old paint off and lots of filler I was down to bare metal and ready to apply some etch. Pannel wipe everything to make sure it was clean and time to play with my new Apollo Spraymate toy.
Overall I'm quite happy with how it looks thought it still has to dry.

I'll get some more updates regarding the body very soon!





Tuesday, 9 October 2012

Big Steps - The Strip Out Begins

Well its been a long while since I've posted anything and lots has changed. After removing the carpets from the boot to find a hole (un) cleverly covered with a carrier bag so as you would expect, a lovely that patch. So whilst preparing to fix this I though I might as well look over everything else. This opened up a whole can of worms which led me to strip out the car a d the. Take the body off!
I'll update with some pics of the welding later but needless to say it gave me plenty of time to practise as I'd never welded before.
As the doors were taken off the openings were braced using some tube steel with the ends flattened and bent then bolted into existing holes.

Also if I was going to remove the body again I would certainly suggest more than 2 people as its is a lot heavier than you may think!






Sunday, 22 January 2012

Bleeding The Brakes, How Hard Can It Be?

This morning I thought I would go out and do some more work on the car, beeding the rear brakes. Now this isnt my first time bleeding brakes so I expected everything to go fine, ish.

I hooked everything up and let the pumping begin, after having to fill the MC twice and still getting nowhere I thought something was wrong, lool under the car and fluid is pouring all over.


I havent connected the rear passenger side pipe to the hose!!!


Get the car back on its wheel and lift the other side and set to work on the rear passenger. I decided to replace the hose but thats not straight forward as the old ome had to be cut off as it was stuck fast. So after that and fitting the new hose I connected it up only to find the bottom pipe was leaking. New pipes needed, great. Needless to say at that point I called it a day!


Published with Blogger-droid v2.0.3

Wednesday, 18 January 2012

Well alot has happened since I last posted including alot of things that a most likely cant remeber. The car was taken off the road about 6 months ago when the back end was stripped off and the diff seals done at Willow Triumph, I also have the rear trunions freed up. The rear U joints have been replaced and then the car was pretty much neglected and not put back together. So just before the Christmas break I managed to get some motivation and get back to work and the car was put back together and on its wheels in a matter of days. Thankfully it's been a mild winter otherwise it would still be on the axle stands. Anyway with a bit of persuasion the car roared back to life, however with no tax or MOT I cant take it for a little rise, probably a good thing as I still need to bleed the brakes.

Next to tend to are a few little holes in the boot floor and then I will have a look at pannel gaps etc.

I am however quite tempted by this kit

http://www.sammio-spyder.com/sammioncordite.html


Then comes the question; do I got for a heavy, thumping 3.5 V8 or a light revy 4AGE 1.6 (possible 20V)?

Thursday, 20 January 2011

Oil Leak From Pulley

I noticed last night that I had a few drops of oil from the front near the radiator, upon further inspection it seemed it was all over the chassis and dripping from there from the timing pulley.
Not having the time to fix it I took it to Willow Triumph who confirmed this and said he could fix it today.
Radiator off, pulley off, timing cover and fan off. Timing chain and sprocket off, all re-fitted with a new gasket, seal and timing chain and its hunky dory now however I was told that I need new steering rack mounts and rear tie bar bushes so I'll get those ordered and fitted in the coming weeks.

Little and often, hopefully that's the way this project is going!

Saturday, 15 January 2011

Start Of The Work 2011 - Gaskets

Welcome back and Happy New Year.

Work on the Spit' has been pretty slow at the moment, I adjusted the fuelling over Christmas only to have to do it again as I replaced an exhaust manifold stud that wasn't in so want to make sure that there wasn't an air leak.

At the same time as having the head gasket done the thermostat gasket was replaced with what I can only describe as a new paper thin gasket. Needless to say this didnt last very long, so a trip to Sportscar Supplies (Newcastle) saw me with a new gasket which you can see is considerably thicker.

Waking today I found the weather was terrible, windy, rainy and generally not nice. Leaving it until about 3 I had my chance (although I had to contend with working in the windy dark.) At the same time I also replaced the exhaust manifold/down pipes gasket (which I got from Willow Triumph) The one I took off was, erm, crispy to say the least.

All done now and hopefully work will speed up so I can get some more updates.

Monday, 15 November 2010

Head Gasket Mk 2

So after replacing the head gasket it managed a whole 8 yes 8 miles before the car died and showed symptoms of the head gasket blown again between two cylinders.
Due to work and not having the time I sent the car to a local garage that I know to be reputable. There the head was skimmed and pressure tested and head gasket replace, exhaust to manifold gasket replaced and also the water pump housing gasket replaced.
Just as I went to collect the car they discovered a small hole in the pipe coming from the back of the water pump to the heating pipes. This was at 5:00pm on a Friday afternoon, does law. 30min minutes later and a quick trip to see Tim at Willow Triumph and a replacement had been sourced and was being fitted. 30 minutes later and the car was back to life.
The next day I changed the HT leads for some red silicone replacements and using a timing light I set up the timing to 10deg before top dead centre (BTDC) the car is now running great.
Hopefully I'll get a picture of the ruined head gasket up soon.
Published with Blogger-droid v1.6.5

Sunday, 31 October 2010

Busy Weekend But Still Defeated


Well after two busy days working on the car, this evening I have decided that I just cant wait until next weekend to look into it further so its going to the garage to get fixed.

I had a complete power failure a week ago and the car would no longer start and it turned out that the head gasket had gone between the first and second cylinder (the photo shows the gasket upside down.

So that was replaced along with the rocker gasket and the inlet/exhaust gasket.
As the coolant had been flushed I also filled it with Holts Speedflush ready to fix it further the next day.
I took the car for a quick drive as per the Speedflush instructions but when I arrived back home the coolant was boiling. Hmmm?

The next day the coolant was flushed and replaced with proper coolant. The water pump was checked by removing the fan and the pump from the housing to check it turned okay. The thermostat was tested by putting it in water and heated to check it opens at the desired temp (around 82degrees C) I also replaced the thermostat gasket at the same time. While the fan was off I changed the fanbelt which turned out that the old belt was only ever so slightly stretched compared to the new one but still it's changed now.

So then the radiator was flushed through with clean water, re-fitted and filled with coolant mixed 2 parts water, 1 part coolant. The coolant was Halfords Silicate (IAT) type which is the preferred type of coolant over organic acid technology (OAT) coolant which is no good for older cars.

Next on the list, replace the points and condenser. These are both straight forward, simply two screws to take the old out and new put in its place. The screw that holds down the points is what is used to set the points gap, with the red part (in my photo) of the points pointing at one of the high points of the rotor, slide the points so that the gap opens and using feeler gauges the gap is set to 0.015" and the screw is tightened.

Next on the hit list was to change the spark plugs. The replacement plugs that I bought were NGK's where as the ones currently fitted were Champion.
Obviously changing spark plugs is straight forward just make sure you use a spark plug socket as you don't want to damage them. So out came 4, 3, 2 and, wait there. I cant get into one because of the alternator. So that had to be slackened off again and the fan belt taken off the alternator pulley so I can slide it out of the way and access is gained. Surprise surprise the plug in 1 is an NGK, it would seem a previous owner/mechanic couldn't be bothered to go through that little bit of work to replace plug 1.

So now that all of that was done I started the car and all was hunky dory apart from a little water getting out of the pipe that connects that thermostat housing to the top of the radiator, no problems, to the box of spares that came with the car.

Now to reap the rewards and take the car out for a drive. No more than a 3 mile run as I wasn't sure I was even going to get back as the car had no power at all. Once back I tried to re-start so I could use my shiny new stroboscopic timing light to adjust the timing but it wouldn't start. Maybe doing it statically first? So I tried to crack the car by hand but it wasn't moving due to the compression, so out came the plugs again and I managed to turn it but couldn't see the mark so I got an assistant to turn the car over to turn the wheel a bit quicker and hopefully see it. At this point I was shot at from cylinder 4 what turned out to be coolant in the cylinder, bad news.

At that point I decided to give up, I'll be calling the garage tomorrow and hopefully get it collected.

With any look the water wont have been compressed and snapped a con rod but either way watch this space.

Thursday, 21 October 2010

Replacement Starter Motor


After the AA call out, being a few hours late for work and not wanting to drive around in the other half car which has flowers on the side I decided to replace the starter motor on the Spitfire when I returned from work.
I already had a second hand starter motor which I had ordered previously from Dave at Spitfire Graveyard. I bought this when the car wouldn't start previously but started eventually with a jump. By time I was home it was cold and plenty dark but I was already committed, this job was getting done.

Car pulled under the security light and wrapped up warm I was ready to go.
I unbolted the top bolt, relay wire, removed the aluminium engine guard to access the bottom bolt and as soon as that was off the starter was ready to come straight out. As you can see from the pic the two look a bit different but my brain was so frozen I thought nothing of it. Offering the new motor up to the engine it was to small! I was not happy. Straight inside E-mail to Dave to ask how to have the "mix up" corrected as soon as possible. When I went back out I had a closer look and realized mine had a fitting spacer that obviously came off and fixed the problem. Oops, now to send a rather embarrassed E-mail to ignore my previous one.

The real test came this morning when I tried to start the car in the cold. It fired straight away with no issues and the car seems to run a bit quieter strangely.


Success, now onto the next item on the list.

It would seem I spoke too soon, about a mile away from home the engine started ticking/knocking then as I pulled up it spewed coolant. I've been told a few things to check so will have to get on that one at the weekend.

Wednesday, 20 October 2010

Hello Winter

Well the cold hit hard and as a shock this morning, as a result the Spit didn't want to start. After lots of trying I gave up and called the AA.
An hour later the car was going but I was told the timing could do with checking, the starter motor and battery replacing even though the battery checks out as good. Luckily I bought a starter motor a few week ago.
Stay tuned
Published with Blogger-droid v1.6.3

Friday, 1 October 2010

New Overflow Hose & Headunit


Granted the update is a day late but better late than never.

Whilst getting some clips for the fuel line hose for the fuel pressure regulator (not yet fitted) I thought I would get some hose and cli
ps to replace that washing machine cold water pipe. Straight forward fit with removing the old, cutting to the same size and re-fitting with jubilee clips. The hardest part was cutting the hose with a Stanley knife blade that was as blunt as a spoon.

I'm sure you'll agree it looks alot better



The car came with a cassette player fitted. Now I could survive with this as it has radio and also and aux input so I could have hooked my phone up to play music. The only problem was, if I was going to have something retro, I would want the standard headunit that came fitted with the car.
After a half hearted search for an original headunit I gave up and went straight to the shop to get a headunit. Nothing flash as there's no point in having Bluetooth connection if you can't hear it over the engine noise.

Fitting was a piece of cake as the wires were already in place for the previous headunit so I just cut them and wired in my new ISO adaptor.
As you can see I had to use the plastic 'face plate' that the old one used as the opening is slightly bigger than a single DIN headunit. I can probably tidy this up a bit better at a latter date aswell as find a better way to have it secured in place.
The next projects for the audio will be to fit 4 13cm speakers, 2 to replace the ones in the rear side panels and 2 to install in the rear panel. The other project is to replace the aerial as the one currently fitted doesn't slide away and so has to be unscrewed every time the cover is getting put on.

Wednesday, 29 September 2010

Fixing Leaking Carbs & Fitting Temperature Sender

Finally some progress, the post finally came today and with it my SU HS42 carb overhaul kit, replacement temperature sender and fuel pressure regulator (not yet fitted.)

So out to work in the rain I go. I took the carbs off so that I could take them inside to work in the dry and warm. After taking the top half and all of the insides out of the first carb in order to replace the jet I realised on the second that none of that was necessary and all I have to do was take it out of the bottom.

I considered simply changing the washer an seals on the existing jets however as the washer and seals were so tightly fitted to the new jets I didn't want to disturb them.






After all was put back together and checked there didnt seem to be any leaks which is always a nice thing, installing the fuel pressure regulator should also help keep it this way for a while but I will have to get some extra fuel line before I do that.

Im sure you will agree they look nice and clean compared to the old ones.



Whilst dirty and under the bonnet I thought I would install the replacement temperature sender. Obviously this on looks alot more like the standard fitted one and miles more like it than the oil pressure sensor I was previously sent.







2 minutes later and it was installed, another job done.

Another thing for me to fix as you can see in the photo to the right is the blue overflow pipe from the rocker to the carb's. Yes your right it is cold water feed pipe from a washing machine. Needless to say that wont be on much longer.

Tuesday, 28 September 2010

Another Day, Another Job Not Completed

After starting with the best intentions even though the weather was a bit grim it dried by the afternoon so a coolant change was on the cards. In short this never happened, I decided to tackle the leading carb. After a closer look it seemed the carb was leaking from the bottom of the main jet where the pipe connects to the float bowel. Aluminum engine shield removed and a little touch on the pipe showed it had nothing holding it in apart from good will. It seems it wasn't catching the seal.
I took apart the other side to check how it went together but looking at that seal it looked very worn also. Not an issue you would think, apart from my carb kit hasn't come so I have no seals. Hopefully tomorrow it will arrive so I can get on.

On the upside I did fit my cover for the first time. More details of that later.
Published with Blogger-droid v1.6.0

Monday, 27 September 2010

More To Add To The List


Well it should be sorted with the temperature sender, it should be coming out in the post tomorrow, and I get to keep the oil pressure switch!

On the downside, after cleaning the float bowl I still have fuel coming out of one of the bowls, rather annoying really so that's to fix. I have been advised that my fuel pump looks like a replacement (not sure what the previous owners have fitted) so I have ordered an adjustable fuel pressure regulator to try and drop the pressure from 6-8psi to 1.5-2.5psi. Hopefully this will fix the problem.
The second thing is that the front left caliper seems to be binding a bit so I've ordered some caliper seals to replace when I replace the wheel cylinders and master cylinder seals.

Temperature Sender Replacement - Part 1


Part 1? How can it be so hard to replace a temperature sender? Read on.....

After an internet shopping spree I have most of the parts I need to complete the bits of work that need to be done to the car. As today it's raining I thought I'll start with something nice and easy, a 2 minute job, replace the temperature sender so the temp gauge in the car works.
Armed with the tools and replacement part I lifted the bonnet to see that the existing sender looks completely different straight away. Time to unscrew and investigate, as it turns out I have been sent an oil pressure switch which as you can see is quite a bit different.

Time to contact the seller and hopefully it can be rectified quickly.